RedditPP Mascot

RedditPP

r/wifi • … • u/G2EZ

FRITZ!Box 5690 Pro + MediaTek RZ616: 5/6 GHz works once after reboot, then reconnect fails

Hi,

I’m trying to troubleshoot a very strange and highly reproducible Wi-Fi issue with my desktop PC.

\*\*Setup:\*\*

\* FRITZ!Box 5690 Pro \* FRITZ!OS 8.25 \* Windows 11 25H2 \* MSI MAG B650 TOMAHAWK WIFI \* MediaTek RZ616 / MT7922 Wi-Fi 6E 160 MHz \* currently using MediaTek driver 3.6.0.1425 \* separate SSIDs for 2.4 / 5 / 6 GHz

The issue is this:

After rebooting the PC, \*\*5 GHz often connects successfully once\*\* and can negotiate up to 2402 Mbps.

If I manually disconnect and then try to reconnect, Windows gets stuck on \*\*“Checking network requirements”\*\* for a while and then says:

\*\*“Can’t connect to this network.”\*\*

6 GHz behaves similarly.

2.4 GHz works reliably, but performance is much worse. My internet connection itself is fine: the FRITZ!Box syncs at roughly 117/37 Mbps, another laptop on 5 GHz gets around 100 Mbps, while my PC usually gets only \\\~40–45 Mbps because it is forced onto 2.4 GHz.

A few things make this especially confusing:

\* the exact same RZ616 works fine with a \*\*5 GHz Wi-Fi 6 / WPA3 iPhone hotspot\*\* \* the same PC worked fine on 5 GHz with my previous \*\*FRITZ!Box 7490\*\* \* other laptops, iPhones and Android devices work normally on 5/6 GHz with the 5690 Pro \* the RZ616 itself can connect to the 5690 Pro at full link speed, just not reliably after disconnecting/reconnecting

I have already tried:

\* multiple MediaTek drivers \* deleting and recreating WLAN profiles \* resetting the Windows network stack \* WPA2-only instead of WPA2/WPA3 \* disabling WPS \* fixed 5 GHz channels \* Wi-Fi 6 mode instead of Wi-Fi 7 on the router \* guest Wi-Fi \* adapter disable/re-enable \* cold reboots

None of this fixes the underlying reconnect problem.

The most interesting part is the router’s support logs.

During a failed 5 GHz connection attempt, the WPA 4-way handshake looks like this:

WPA: sending 1/4 msg of 4-Way Handshake WPA: received EAPOL-Key frame (2/4 Pairwise) WPA: sending 3/4 msg of 4-Way Handshake WPA: sending 3/4 msg of 4-Way Handshake WPA: sending 3/4 msg of 4-Way Handshake

So the AP receives 2/4, repeatedly sends 3/4, but the handshake never completes with 4/4.

At the same time, the FRITZ!Box logs messages like:

link-STA not found. Check MLO mac address list ap\_get\_mlo\_sta: STA ... not found for AP with MLD MAC ... ERROR: Null Pointer ap\_get\_sta\_mlo\_obj ERROR: NULL Pointer ap\_get\_ft\_ds\_ml\_sta

On 2.4 GHz, the exact same client completes the handshake normally:

1/4 -> 2/4 -> 3/4 -> 4/4 AP-STA-CONNECTED pairwise key handshake completed EAPOL-4WAY-HS-COMPLETED

Another weird clue: Windows sometimes also hangs on \*\*“Restarting…”\*\* when the RZ616 is enabled. If I disable the Wi-Fi adapter in Device Manager, restarting Windows works normally.

So at this point I’m unsure whether this is:

\* a MediaTek RZ616 driver/firmware bug \* a FRITZ!Box 5690 Pro / FRITZ!OS 8.25 interoperability bug \* some MLO-related state issue being triggered by the RZ616 \* or a combination of both

Has anyone seen similar \*\*“works once after reboot, then reconnect fails”\*\* behavior with the RZ616 / MT7922?

And if anyone is familiar with WPA/EAPOL debugging: does the repeated 3/4 behavior point more strongly to the client failing to process/respond, or could the AP-side MLO state errors be causing the client to reject/drop message 3/4?

I’ve already sent the full support logs to AVM and asked them to escalate it to their WLAN/firmware team.

— 0