RedditPP Mascot

RedditPP

r/woodstoving • … • u/RollingEasement

Finally lined flue: Are offset adapters problematic and must I forfeit damper

For decades, this Timberline insert just vented its offgases into the fireplace smoke chamber, and then the gases went up a clay flue liner with interior dimensions of about 6.5 X 11". I would occasionally sweep the chimney with a rectangular brush, but this year I finally decided to have a 7" liner installed, which is about the same cross section as the 42-square inch outlet of the stove when the damper does not constrict outlet (It's an ovalized rectangle of 6.5" width and 7-5/8" length.) The installer is going to come back in two weeks to redo the connection between the stove and liner, so I have two weeks to think about what I should really seek in the redo.

My first question concerns the damper, which is a flat piece of iron that just slides on the top of the stove. The installers told me that I don't really need a damper, which seemed like a convenient thing for them to say; but is it even reasonably feasible to keep that damper given the way a liner connects to the stove? The damper has seemed to be only useful when I keep the door open for awhile using that screen shown on the right--but it was not really needed even then. Yet I think it will be more needed in the future because the draw from the chimney seems to be alot more powerful now than previously. Chimney is 22 feet.

Second: Even with a bend at the bottom, the new flue liner is about 1/2 foot behind where gases come out the top of the stove; so installer made an offset adapter, which is 3" high and 10" wide, that is, the cross section is only 30 square inches which is less than the stove outlet. Because they mis-measured the adapter, the stove is now two inches farther into the fireplace than it had been and for which it was designed, which is why they need to come back to finish the job. Because there is some overlap in the offset now, as in the sketch for the offset sold on[ Amazon](https://www.amazon.com/Fireside-Chimney-Supply-Insert-adaptor/dp/B009KUTN7C/ref=sr_1_1?crid=13LOPKNUCSUFC&dib=eyJ2IjoiMSJ9.VRA4C8G5RUCCwWPJQ2vJtHjjJb-DR5fzKl7ljVHWwgBpTBkhN0m5nB-6a-w8TN4qcKL_VwUVJ2ZzxCQg8ETmORTG8EUa16BI3GhqzpHLLdT30oQssdjBQOcbbTdpW03d_a0eKURqsFm7aOOPuQadigGfNJykGm1Ngh0urZEaHKfDdyfVoXfMleN2FtGkTWCuvZJUcSEQ0uswWhjCwXSB71UNyDsT2MTLycABawBCEClVgTYEb7oB0pzYXt3ai87p-ZiPDiX8zjozJbJtldov9nXvAQp7Ff2ofWfELtDoP1s.i6bLL2hgw1Ejb8ZauW5wTbLqhYxyCFKk07o5HxC_szo&dib_tag=se&keywords=wood%2Bstove%2Boffset%2Badapter&qid=1760380234&sprefix=wood%2Bstove%2Boffset%2Badapter%2Caps%2C87&sr=8-1&th=1), the effective cross section of the adapter is probably closer to 35 square inches. But once the stove moves forward two inches, there will be no vertical overlap so a 10" X 3" cross section seems to have greater potential to be a constriction. And yet, if they just made it 12" wide instead, there would be no constriction. (I doubt there is room for the 5" height in the adapter sold by Amazon.) The installer now says that they will use a standard offset adapter actually designed for the Timberline, he but won't give me the details so I am in the dark about what that actually means other than--one hopes--it will both fit and have sufficient cross section. So I won't really know what it is until they show up with it. Does such an adapter actually exist on the market so that I can get details?

Thanks.

— 0