RedditPP Mascot

RedditPP

r/woodstoving • … • u/lucentcb

One year after finding this subreddit, I'm a convert (my DIY 90s ZC fireplace to woodstove conversion)

I'm not totally finished with this project yet, but I'm pretty excited about it and wanted to share my progress!

This time last year, I was trying to find \*something\* to do to make the fireplace in our basement suck less. I had resorted to making an insulated cover for it, which did help a bit (I had covered it in a fake brick wrap for fun, and the plastic visibly shifted with the draft, which gave it the creepy feature of looking like it was breathing). But even if we used it, it barely put out any heat. After some homework, it seemed like my only options were to either seal it off entirely, or totally gut and replace the entire thing.

Even if having it replaced wasn't way out of my price range, I didn't want to go through all the trouble if in the end, it still wouldn't make much of a difference in our cold basement. And that's when I found this subreddit.

A wood stove seemed like the more economical option, it was conceivably DIY-able, and I had the clearance for an alcove install...so I went for it. I bought a Drolet Columbia II in the spring, so I'd have the summer and fall to work on it and have it ready just in time for winter.

Removing the old fireplace led to some discoveries:

* It was very poorly insulated (this was not a surprise in the slightest) * There was severe water damage on one side of the small roof, requiring a side project to repair it with proper flashing * The other side of the small roof had the same issue with flashing, but was apparently protected from the wind and rain, because rather than water damage, I found the remains of a yellowjacket nest. This happened a few years ago, and we had it dealt with, but it was unsettling to realize just how many were in there and what little kept them from making it all the way into the house (but man, what a nightmare this would have been if I found a \*live\* hive this way). * The air intake vent in the fireplace was permanently stuck open (which helped explain the draft...) * The chimney was basically resting atop the fireplace. This seems like a common thing based on my research, but I did wonder why they even bothered nailing the support straps when they were so loose they were providing zero support of any kind. I managed to get just enough leverage to work a board underneath it to hold it up while I got the fireplace out.

Next up, chimney removal. This required going on the roof, which I did not enjoy (but I did invest in a safety harness). The rain cap did \*not\* want to come off, but I wound up just knocking out the board I had holding up the chimney and letting the chimney cap finish it off when it dropped down. My strategy was basically to pry apart each section and yank it out, sending the rest of the chimney crashing down. This was surprisingly effective! And very noisy.

Installing the new chimney involved removing siding in two places, cutting an opening in the sheathing, screwing the sections together, and sealing everything back up--pretty straightforward, outside of the small offset required to keep things lined up which was a pain to get leveled properly. I was also very happy to be done having to go on the roof.

Inside, I built up an elevated hearth using a section of basement foundation I'd just recently cut out to add a walkout. I had proper clearances to everything existing, but I framed out the alcove with metal studs to be able to insulate the foundation and put up Durock. I used some steel panels for the back in the hopes that it would help radiate some heat outward, with ledger stone to finish the surround.

The last major step was to do something I've wanted to do since we moved in over a decade ago--remove the super 90s corner TV cabinet. I'm getting off topic here, but that thing was the sturdiest thing in the house. It was composed of 2x4s, drywall, and plywood, and held together mostly with framing nails. It also helped to hide a drain pipe that came down behind it, and I'm convinced it was a builder's pet project that they were very proud of. And they should have been, because it was legitimately done well. There may have been some other corners cut in the construction of our house, but damn it, that cabinet was going to hold up your 400 pound CRT until the end of days. But it did not age well. It only remained because of the effort required to remove it--not just dismantling it, but also having to re-floor the corner (because the cabinet is built directly over the concrete) and finding a better way to deal with the pipe behind it.

With that finally dealt with, I bought a bunch of shelves, cut them down to the widths I needed, and installed them. I still need to figure out how I want to finish the left side. The TV will be mounted in the corner, and I'll probably buy an additional shelf so I can make the sides of the stone symmetrical (the last picture has a leftover piece in that spot I put there to help myself visualize it). Other remaining tasks:

* Stain the beam to match the shelves * Clean up the stone corners (the mitered cuts don't look great up close) * Finish alcove ceiling (a metal panel at an angle to help move heat out of the alcove) * Trim between the slate and wood floor

But man, I kinda love this thing. Our basement usually sits at \~61 degrees on a normal winter day (with the thermostat set at 68) and within an hour or so of getting a good fire going, it's the warmest room in the house. I wish I'd known this was an option years ago, although it's only in the last few years that I built up the DIY confidence to take this on. It's definitely DIY-able, but you need to be willing to do a lot of research and a lot of labor. I'm doing my part to keep the cycle going and help convince the next person to go for it.

(Cat tax at the end of the pictures showing them enjoying the fire as well)

— 0